Maintenance module (MM) is designed to control serviceability, diagnostics and renewal of Line Replacement Units LRU) being incorporated in the Radar: digital, digital-to-analog and analog cells; high frequency units and subunits; PCBs and secondary power supply units.
MM Incorporates the workstatIons:
WS-1 (Workstation 1) is designed for diagnostics and fault finding up to the element level (a group of elements) of
digital and digital-to-analog LRUs based on TTL, CMOS or mixed TTL-CMOS logic as well as LRUs having analog elements with signal levels over the range from
WS-1 is made applying the automated diagnostic complex and is completed with multi-purpose programmer "UNIPROG".
The diagnostic complex consists of hardware, software and repair databases for the tested LRUs.
The hardware consists of 135-channel test-processor, 16-channel logic and signature analyzer and 6-channel analog
generator and performs the following functions:
· Testing of PCBs via connectors with simultaneous recording of the PCS reaction for test;
· In-circuit testing of the PCB and elements;
· Providing LRUs under test with power supply.
WS-2 (Workstation 2) is the PC-based measuring-diagnostic complex, which is designed to diagnose and measure the high-frequency LRU parameters.
The complex incorporates:
· RF and UHF units of oscillators being controlled;
· Digital oscilloscope;
· Spectrum analyzer.
WS-3 (Workstation 3) is a multi-purpose workstation, intended for diagnostics of failed cells, assemblies, subunits and units providing switching, check and control, obtaining secondary voltages, processing and onversion of analog signals as part of the radar units and cabinets. WS-3 possesses the built-in facilities of protection, control and check of its main parameters.
WS-4 (Workstation 4) is a multi-purpose repair station. It is equipped with a set of fixtures, tools and special-purpose equipment.
The dismounting of faulty radio elements, the radio elements performing, soldering of newly mounted elements and varnishing are accomplished at WS-4
Main functions:
- remote control of Radars 36D6M, 80K6K1;
- collection and processing of Radar data with digital output in composition of air defense electronic technical units with air picture data output to command posts by wire and satellite channels;
- collection of Radar data from remote sources, forming of combined air picture;
- control of fighter aviation pilots actions;
- target data transmission to AAMC (option).
RCP-1 composition:
- Personnel workstations;
- Radar control operator workstation;
- Navigator workstation;
- Commander workstation;
- Data processor;
- Modems, radio-bridges;
- Satellite modem (option);
- Radio station for communication with pilots;
- Radio station for tactical – command communication;
- Electric power supply equipment;
- Life-supporting equipment.
PURPOSE
Built-in radar interrogator (BRI) 69Л01 of system МК ХА,МК ХIIand RBS is designed to perform the following tasks:
- general identification of airborne objects equipped with radar transponders
- individual identification of airborne objects equipped with transponders
- cryptographically secure identification of airborne objects equipped with transponders and cryptocomputers
- determination of the aircraft identification code to meet the needs of ATC
- determination of the aircraft azimuth
- determination of slant range to the aircraft
- determination of the aircraft barometric altitude
- determination of the flag of SPIpulse receiving
- determination of the civil aircrafts' emergency codes
- determination of the flag of military aircraft wreck
Built-in radar interrogator 69Л01 meets the requirements of NATO (STANAG 4193) and ICAO standards.
PRINCIPAL FEATURES
High-stable solid-state transmitter with programmable
output power
Log receiver with amplitude characteristic of variable
slope
Line receiver with wide dynamic range
Digital programmable in-built extractor
Individual transmitters for main channel and side-lobe
suppression channel
Side-lobe suppression system for transmitting
Programmable system of side-lobe suppression for
receiving
Programmable STC system
Programmable one-turn and two-turn mode of
interrogation interleaving
In-built automatic control and diagnostic system
The solid-state stand-alone mobile secondary radar with the phased antenna array operates under standards of both the NATO IFF system Mk XA (Mk XII), "Parol" idantification system and international ATC system RBS.
Tthe radar is designed to issue radar data to units of radio-technical troops of air forces, AAMT of air forces, ground forces air defense troops as well as to ATC services.
MAIN SPECIFICATIONS:
| Maximum rarad operations limits: |
|
| in range, km | 2…360 |
| in azimuth, deg. | 360 |
| in elevation, deg. | 0,5...45 |
| in altitude, km | 25 |
| RBS error in coordinate determination: | |
| in range, m | ≤100 |
| in azimuth, min. | 12' |
| Track information quality: |
|
| track factor | 0,98 |
| false track factor | 0,0001 |
| Throughput, tracks | >250 |
| Output information | track |
| Data read-out and transfer | Automatic via DTE |
Modern high-mobility VHF-band radar with digital phased antenna array is designed to detect all types of existing and advanced air targets, including UAVs and Stealthy aircrafts.
MAIN SPECIFICATIONS:
| Radar operation limits: | |
| in range, km | 1,5...400 |
| in azimuth, deg | 360 |
| in elevation, deg | 0...40 / 70 |
| in altitude, km | 40 |
| Target detection range, RCS=3-5 m2 (at P=0,8 F=10-6): | |
| at flight altitude 10-30 km | 300...360 km |
| at flight altitude 1-5 km | 260 km |
| at flight altitude 100 m | 27 km |
| Clutter suppression, dB | > 50 |
| Deployment/closing time, min | 5 / 3 |
tel. +38 (061) 271-21-52
e-mail: iskra@iskra.zp.ua
84, Mahistralna St.,